How To Flashing videocon z40 quad

keyword : How To Flashing videocon z40 quad for bootloop , How To Flashing videocon z40 quad for softbrick , How To Flashing videocon z40 quad for hardbrick , How To Flashing videocon z40 quad Error Camera , How To Flashing videocon z40 quad blank screen , How To Flashing videocon z40 quad lost password , How To Flashing videocon z40 quad stuck logo , How To Flashing videocon z40 quad new 2017. How To Flashing videocon z40 quad repair phone. How To Flashing videocon z40 quad Upgrade Firmware , How To Flashing videocon z40 quad via Flashtool , How To Flashing videocon z40 quad for unspecified error , How To Flashing videocon z40 quad mode Edl error , How To Flashing videocon z40 quad bootlooader relock and unlock.

Download File Firmware and Flashtool plus Video Tutorial compressed:

• DOWNLOAD FILE via Mediafire HERE
• DOWNLOAD FILE via Googledrive HERE

do not forget there are some additional tips from me:

Further to the following stage :

1. Duplicate the document to Sd Card

2.boot into recuperation mode, in the document as of now exists as .pdf open a full instructional exercise and take after the guidelines. anybody utilizing blazing programming.

3. When've taken after the greater part of the conditions please check the telephone has been typical what is most certainly not.

4.Characteristic components EMMC highlight of blazing not harmed in the street, still can wipe information reserve. yet, introduce the upgrade shape sd card can not or won't runing.

5.booting first after introduce rom considerable lot of time of around 15 minutes. Try not to rush to evacuate the battery. hold up until the framework completes the process of booting.

critical: before doing anything on the telephone to do the information reinforcement already. can pass CMW, recuperation, twrp please find on the off chance that you lack.

How To Flashing videocon z40 quad

if you’ve done everything you can to tuneyour multicopter’s flight characteristics and are still looking for better performancethe simonk electronic speed controller firmware may be the way to get smoother flights witha more locked in feel. today i’m going to show you how to flash turnigy multistar escswith simonk firmware. this same procedure can be used on other atmel based escs withonly minor changes. first you’ll need to get some hardware….a usbasp programmer i bought this one for under ten dollars on amazon. and an atmegaavr socket flashing tool like this one from hobbyking…. some people make their own wiringharnesses but this tool clips right onto the atmel chip and makes the job super simple.there is a link in the description for both

of these items. next you’ll need to download some software…do a quick google search for kk multicopter flash tool. it should come up as the firstsearch result. the website is in german so you may have to used google translate to readit. scroll down until you find the downloads area. and download the appropriate softwarefor your operating system. next you’ll want to go to the rapid escdatabase and find out what the appropriate firmware is for the escs you are going toflash. for my 30a turnigy multistar escs i will use the kda hex. plug the socket programmer into the usbaspand make sure the jumper on the usbasp board

is set to five volts. that way your computercan provide power to the esc while flashing the firmware. then plug it into an open usb port on yourcomputer. install and run the kk multicopter flash tooland make the following settings. set the programmer to usbasp. set the controller to atmega 8based brushless esc plus enable boot loader. then select the firmware for your esc thatwas listed in the rapid esc database. with the esc you’re going to flash on aclean surface carefully cut open the protective heat shrink. make sure you don’t cut toodeep and damage any components or electrical traces. remove the heat shrink.

the main processor is keyed with a dot inone corner so is the programming socket. align the dot on the programming socket withthe dot on the atmega chip and seat it firmly. press the go button in the kk multicopterflash software. in the event of a failure the text will turnred, double check that the programming socket is seated properly and try again. hold theprogramming socket on the chip until the process finishes and the readout says “flashingof firmware was successful” you can reheat shrink the escs or i usuallyjust replace the cover and seal up the seam with a piece of tape.

that’s it… repeat the process for as manyescs as you need.