Thursday, February 2, 2017

How To Flashing cubot one

keyword : How To Flashing cubot one for bootloop , How To Flashing cubot one for softbrick , How To Flashing cubot one for hardbrick , How To Flashing cubot one Error Camera , How To Flashing cubot one blank screen , How To Flashing cubot one lost password , How To Flashing cubot one stuck logo , How To Flashing cubot one new 2017. How To Flashing cubot one repair phone. How To Flashing cubot one Upgrade Firmware , How To Flashing cubot one via Flashtool , How To Flashing cubot one for unspecified error , How To Flashing cubot one mode Edl error , How To Flashing cubot one bootlooader relock and unlock.

Download File Firmware and Flashtool plus Video Tutorial compressed:

do not forget there are some additional tips from me:

Further to the following stage :
1. Duplicate the document to Sd Card
2.boot into recuperation mode, in the document as of now exists as .pdf open a full instructional exercise and take after the guidelines. anybody utilizing blazing programming.
3. When've taken after the greater part of the conditions please check the telephone has been typical what is most certainly not.
4.Characteristic components EMMC highlight of blazing not harmed in the street, still can wipe information reserve. yet, introduce the upgrade shape sd card can not or won't runing.
5.booting first after introduce rom considerable lot of time of around 15 minutes. Try not to rush to evacuate the battery. hold up until the framework completes the process of booting.
critical: before doing anything on the telephone to do the information reinforcement already. can pass CMW, recuperation, twrp please find on the off chance that you lack.

How To Flashing cubot one

so today we’re going to take apart the ztefury from sprint. to start off with there are 7 screws all around the outside. i’mgoing to speed this up so you don’t have to watch me taking off each one. one of thescrews is underneath that little sticker, it’s the void sticker. just so you know,by taking apart the phone and stuff you void all the manufacturer’s warranties. but it’sa pretty simple process so you shouldn’t have too many problems. to start unclippingthe screen from the frame, i started at the bottom of it. then you can see as i take mypry tool and kind of slide it along the edge here. there are probably about 4 clips oneither side and then a few at the top and the bottom that snap open. they separate rightwhere the color meets the silver. when you

pull the two pieces apart make sure you makesure that the motherboard stays down on the top of it next to the screen and doesn’tpull away with the bottom half of the phone. as you can see, all of the different componentsof this phone are soldered onto the board, so there’s really nothing else that youcan replace without getting super technical into the soldering aspect. there are threeribbon cables attached to the screen: the bottom one i just did by the battery, thisone right here that goes to the screen, and then this one right here by the top. basicallyyou just take the little tiny clip and slip it up. flip it up right along the edge andthen you wiggle the ribbon cable out very gently from the edge. they are pretty, youknow, resilient, so you shouldn’t have too

many problems, you know, ripping them or tearingthem or anything as long as you’re fairly gentle. there are no screws holding the motherboarddown so just pull away. and then this is the whole screen. putting it back together. themotherboard does kind of clip into place….not clip so much, but it sits really firmly betweenthe screw holes. and then get the ribbon cables back into place. that was one of the hardestparts, getting them to line up. so once again just be gentle with them. and then once theribbon cable’s all the way inside of the little holster for it, you can just slidedown the little latch which locks it all into place. the back plastic itself just clips right backon again. make sure you run your hands along

both sides, and make sure all the latchesare in place. then you can take all the screws and put them back in. and any latches thatyou missed, like any clips that didn’t clip into place, will clip into place once youget the screws inside. toss in the battery and you’re good to go. anyway, i do postlots of phone teardown/rebuild videos, at least once a week. so go ahead and “like”if this video helped you, and don’t forget to subscribe. thanks!

Related Posts:

0 comments:

Post a Comment